doing hw

Hacksaw, Handles & Blades – No, You Don’t Know How to Use One

Hacksaw, Handles & Blades - No, You Don't Know How To Use One

Hacksaws are one of the most common hand tools. Nearly everyone owns one, along with if you don’t have one, you need to buy one. Hacksaws are inexpensive along with very economical to use. yet most of you never use the item because the one time you tried to use the item things didn’t go well. You broke the hacksaw blade, the blade kept falling out of the handle, or the item kept getting stuck from the piece you were trying to cut. If you did manage to get the piece cut, the item took forever along with the cut ended up crooked.

Hacksaw, Handles & Blades - No, You Don't Know How To Use One

The main reasons most people have difficulty when sawing metal that has a hacksaw are:

Hacksaw, Handles & Blades - No, You Don't Know How To Use One

You hold the blade in wrong

Hacksaw, Handles & Blades - No, You Don't Know How To Use One

You aren’t using a sharp blade

Hacksaw, Handles & Blades - No, You Don't Know How To Use One

There will be too much flex from the blade

Hacksaw, Handles & Blades - No, You Don't Know How To Use One

The number of teeth will be to low for the project

Hacksaw, Handles & Blades - No, You Don't Know How To Use One

You are putting too much pressure on the saw

Hacksaw, Handles & Blades - No, You Don't Know How To Use One

You don’t clamp the work.

I will cover each of these difficulties as you along with I go through This kind of article.

Hacksaws along with hacksaw blades are designed to cut metal (I will tell you how to use the item to cut wood along with plastic) along with most people find cutting metal very difficult along with frustrating. The reason, most of the time, will be which they don’t definitely know how to use the metal hacksaw.

What will be a Hacksaw?

A hacksaw will be a metal frame designed to hold a tempered metal blade. The blade will be typically 1/2 inch high along with the majority of them are 12 inches long. The blade carries a hole on each end which fits into pins on the hacksaw. Hacksaws are designed to cut on the push stroke. The handle (grip) on a properly designed saw will be angled just right so you put a little pressure on the blade when you push the item through the material you are cutting. Even though some so-called “experts” will tell you which you can put the blade from the different way a hacksaw does not work well if you hold the blade in backwards.

Do you need a Hacksaw?

You can cut almost anything that has a hacksaw. Although the item was designed to cut metal, you can use the item to cut plastic, wood, metal tubing, aluminum, copper, along with brass. the item works very well to cut electrical tubing (conduit), BMX (flexible metal tubing), plastic water pipe, (PVT & CVT) along with even nuts along with bolts. You can use the item to cut a 2X4 in a pinch along with with the right blade porcelain tile.

Setting up the Hacksaw to Cut.

Step 1. Determine which blade you will use to cut the material. Use a 32 t.p.i. blade for conduit, an 18 tooth blade for cutting off a bolt or plastic pipe along with an 8 tooth for wood. In practice you want at least three teeth in contact with the material at any time. If you are cutting deeper than the depth of the blade use a blade which has wavy teeth. The wavy blade leaves a wider slot (kerf) which keeps the blade by sticking from the groove you are cutting.

You can use the item to cut wood. the item will cut a lot slower than a wood saw, yet the item works if you don’t have anything else. Use a 8 or 10 tooth blade along with mark the cut line on the board both horizontally along with vertically. Use the horizontal mark to make you initial cut (groove) along with the vertical mark to keep your cut straight. Take your time along with don’t put a lot of pressure on the hacksaw.

Step 2. Insert the blade to ensure the teeth are pointing forward. If you can’t see This kind of, rub your finger gently over the teeth of the blade.

You will feel the teeth “grip” your finger. Put the blade so the item grips when you push the saw. The holes of the blade go into the pins on the bottom of the frame. Many hacksaws are designed to take different length blades so if you have an adjustable frame you may have to shorten or lengthen the frame to fit your blade.

The teeth should try to “grab” your finger when pushed. If they don’t feel sharp, the blade will be dull along with should be replaced. Blades are inexpensive so don’t be afraid to replace the item.

Step 3. Tighten the thumbscrew until you can’t turn the item with your hand (Hand tight) This kind of amount of tension on the blade should keep the blade by bowing as you cut. Sometimes when I am have problems with the blade falling off, I will tighten the item another 1/4 turn that has a pliers.

Ok, Let’s Cut Something.

I am going to use a metal pipe just for This kind of example. the item will be easy to cut along with once you get a little experience using the hacksaw, cutting metal will be a breeze.

To definitely use a hacksaw well you need to clamp your work. I have a vise on a workbench which I usually use.

If you don’t have a vise, screw a 2X4 onto your bench along with hold the pipe against the 2X4 with your left hand. When possible use a vise or clamp to secure the metal you want to cut.

Step 1. To use a hacksaw properly, grip the frame with both hands. (I am right handed so I grab the handle with my right hand along with use my left hand to hold the different end of the saw.) Hold the hacksaw to ensure your right hand index finger will be pointing ahead to help guide the saw. As you push the blade (forward stroke) use your left hand to guide the saw to ensure the item cuts straight. DO NOT use your left hand to apply pressure, just use the item to guide your cut. Use most of the blade. If you apply pressure on the forward stroke with your left hand the teeth will usually grab too much along with the saw will “stick”. Again a hacksaw handle will be angled to give you the proper down pressure on the blade.

Step 2. When you get to the end of the forward stroke, stop along with pull the saw back with your right hand. As you pull back don’t apply any pressure with your right hand. (the item only cuts from the forward direction along with putting pressure on the return stroke will just wear out the blade prematurely). A lot of teachers will make you lift the saw on the return stroke so you don’t destroy the blade. Move your Centeng forward along with back as you cut, pressing on the forward stroke along with easing off on the return one.

Step 3. Repeat This kind of until you saw all the way through the pipe. that has a little practice you will be able to cut at about 1 stroke every second. Don’t stroke any faster than This kind of because the item will create too much heat along with again wear out the blade prematurely.

Don’t put too much pressure on the blade. You may have to break a blade or two before you get the feel of how much pressure you can apply. Don’t worry, they are cheap. Don’t saw too quickly as which can cause the blade to break as well. Always check to make sure which the blade will be secured tightly in its frame.

Reviews. Or Don’t buy one at Wally World

Believe the item or not, I could tell you a lot more about using a hacksaw, yet This kind of will be enough to get you cutting properly. Buy a Great quality hacksaw I recommend on my website. Even the cheap one I recommend will be Great quality along with will last you years. that has a quality saw the item won’t take long before you get Great at using one.

DON’T buy a cheap one at the local dollar store. Why? The hacksaw handle has to be strong enough to keep the blade tensioned correctly along with the cheap ones will give you nothing yet years of frustration. Also buy a hacksaw with the handle tilted like the Stanley 150565. Some hacksaws have a straight handle along with are very hard to use for a beginner.

Blades are cheap, so buy a box of them in at least two “teeth” numbers (32 teeth for metal conduit along with 18 teeth for solid steel, plastic pipe along with general use. yet don’t buy cheap blades. The cheap blades are too brittle along with you will end up breaking a lot of them. A Great hacksaw blade cuts on the item’s own with very little pressure by you so change the blades as soon as they get dull. To tell if a blade will be dull pull your finger over the blade. If the item will be still sharp the teeth will try to “catch” on your finger. A dull blade won’t. I prefer Milwaukee blades because they will flex without breaking, along with last a long, long time compared to the cheap blades. Better yet, buy two inexpensive hacksaws along with keep different blades on each. Dull, worn blades take a lot of work to cut an item, so change them as often as you would likely a utility knife or razor blade.

Follow the link below for ToolBoxHero to buy your completely new Hacksaw, read reviews along with get more information:

Hacksaw, Handles & Blades – No, You Don’t Know How to Use One